AOCM6000
High-Density FTTx Communication Switch
AOCM6000 Datasheet
AOCM6000 Firmware - P2P_4.1.2B_35084_10MAY2016
产品简介
The AOCM6000 is a carrier-grade switching/routing platform providing access & aggregation capabilities for PBN’s FTTx solutions. The latest upgrade to second generation will provides higher performance and lower cost.
The largest unit is a 19” sub-rack with 12 RU height, and ten card slots. Two slots are dedicated to redundant switch/controller cards and eight slots are allocated for line cards. Designed for high-density FTTH deployments, the platform is a real workhorse, capable of supporting up to 384 ActiveEthernet subscribers or up to 8192 EPON subscribers in a 1:64 split environment. Or of course, a mix of both technologies.
Designed for modularity, this mainframe is able to support ActiveEthernet subscribers with 24 or with 48 ports per line card for Gigabit Ethernet optical subscriber lines. The high-density EPON OLT cards feature 16 port SFP-based optical line terminals.
The power supply units are available for battery or for universal mains systems. Uplink cards are available with up to 4x 10 Gbps ports for SFP+ plug-ins.
|
|
| Chassis | |
AOCM-60-CH12
|
|
| Controller card slots | 2 controller card slots |
| Line card slots | 8 line card slots |
| CPU | RISC 800 MHz |
| Flash | 16 MB |
| SDRAM | 512 MB (up to 1 GB) |
| L3 forwarding rate | Full wire-speed filtering and forwarding, 143 ~ 572 Mpps |
| Backplane bandwidth | Passive backplane with 2.6 Tbps throughput capacity |
| Switching fabric Super Engine | 384 / 768 Gbps |
| Switching mode | Store-and-forward |
| 802.1Q VLAN | 1 ~ 4094 |
AOCM-60-CH09
|
|
| Controller card slots | 2 controller card slots |
| Line card slots | 4 line card slots |
AOCM-60-CH06
|
|
| Controller card slots | 1 controller card slot |
| Line card slots | 2 line card slots |
|
Features |
|||
| Spanning Tree | 802.1D (STP), 802.1w (RSTP), 802.1s (MSTP) | ||
| Routing Protocol | RIP v1/2, OSPF, BGP, IS-IS | ||
| MPLS | Supported | ||
| IPv6 | Supported | ||
| Multicast Protocol | IGMP, PIM-SM, PIM-DM | ||
| QoS | 8 dispatching queues per port, supports 802.1p, ToS, application port control, DiffServ, WRR, SP, SWRR, etc. | ||
| ACL | Standard and Extended ACL, supports IP based, source/destination IP, L3 IP protocol, TCP/UDP port, IP priority, ToS and time ranger ACL | ||
| MAC Control | Supports port/MAC binding, MAC ACL | ||
| VLAN | Port-based VLAN, 802.1Q, supports GVRP, PVLAN, Super VLAN Stacking (QinQ) | ||
| Flow Control | HOL blocking prevention, Half-duplex: Back pressure, Full-duplex: IEEE 802.3x | ||
| ARP | Supported | ||
| DHCP | Supports Client, Relay, Server | ||
| Port Aggregation | Supports 802.3ad, loading balance | ||
| Customer Access | Supports 802.1x | ||
| AAA | Supports RADIUS | ||
| Port Mirroring | Supported | ||
| Broadcast Control | Supported | ||
| Security | Supports MSU redundancy, hot-swapped, VRRP | ||
| Temperature | 0 ~ 50℃ | ||
| RMON | 1, 2, 3, 9 | ||
| IEEE Standard | IEEE 802.1D IEEE 802.3 IEEE 802.3u IEEE 802.3ad IEEE 802.3x IEEE 802.3z IEEE 802.1Q IEEE 802.1p IEEE 802.1w IEEE 802.1x |
||
| Console Interface | CLI, Web | ||
| Console Port | RS-232 | ||
| Telnet | Supported | ||
| SNMP (MIB) | v1 / v2 / v3 | ||
| SysLog | Supported | ||
* Subject to change without further notice
| The AOCM6000 series switches are ideal for use in centralized FTTx deployments as well as aggregation switches with multiple remote hub-sites. The application diagram represents a typical hybrid HFC FTTx scenario with CATV overlay utilizing AIMA3000 technology from PBN. Based on actual growth of the P2MP or P2P FTTX subscribers, the AOCM3000 switches can be deployed in a cascading fashion, which allows simple management as if there was only a single switch deployed.
For the CATV overlay components, the larger AIMA3000 carrier-grade RF headend solution can be scaled down based on operator needs to PBN’s 1RU EDFA and LTE product line. |
 |
|
SFP plug-ins |
|
|
SFP-EPON-20-SCPC |
EPON – 1.25 Gbps, 20 km, TX = 1490 nm, RX = 1310 nm, SC/PC blue, PBN PM410 compliant |
| SFP optical plug-ins must be ordered separately and are not part of the line card delivery. | |
|
SFP+ plug-ins |
|
| SFP+-GX3131-LCPC |
SFP+ plug-in, 10 Gbps, 10 km, TX = 1310/RX wide, on two single-mode fibers, LC/PC blue |
|
SFP+-GX55ER-LCPC |
SFP+ plug-in, 10 Gbps, 40 km, TX = 1510/RX wide, on two single-mode fibers, LC/PC blue |
|
SFP+-GX55ZR-LCPC |
SFP+ plug-in, 10 Gbps, 80 km, TX = 1510/RX wide, on two single-mode fibers, LC/PC blue |
|
SFP+-GX850M-LCPC |
SFP+ plug-in, 10 Gbps, 300 m, TX/RX 850 nm, on two multimode fibers |
|
SFP+-GXCWxx-LCPC |
SFP+ plug-in, 10 Gbps, 80 km, TX = CWDM variable wavelength, on two single-mode fibers |
| XFP optical plug-ins must be ordered separately and are not part of the line card delivery. | |
|
Model No. |
|
| AOCM-60-CH06-G2 |
Chassis 19”, 6RU, 2 line card slots, 1 controller slot, dual power supply slots, empty. Including AOCM-60-CH06-FAN-MODULE |
| AOCM-60-CH09-G2 |
Chassis 19”, 9RU, 4 line card slots, 2 controller slots, dual power supply slots, empty. Including AOCM-60-CH09-FAN-MODULE |
| AOCM-60-CH12-G2 |
Chassis 19”, 12RU, 8 line card slots, 2 controller slots, dual power supply slots, empty. Including AOCM-60-CH12-FAN-MODULE |
|
AOCM-60-B |
Power supply unit 1 kVA 48 Vdc for AOCM-60-CH06/CH09/CH12 and all G2 chassis |
|
AOCM-60-M-XX |
Power supply unit 1 kVA 110/230 Vac 50/60 Hz for AOCM-60-CH12, Power Cable for XX, XX: AU, CN, CH, EU (not for use in UK/CH), UK, US |
| AOCM-60-S-XX | Power supply unit 600 W 110/230 Vac 50/60 Hz for AOCM-60-CH06/09, Power Cable for XX, XX: AU, CN, CH, EU (not for use in UK/CH), UK, US |
| AOCM-60-CH06-FAN-MODULE | Fan module for AOCM-60-CH06 or AOCM-60-CH06-G2 |
| AOCM-60-CH09-FAN-MODULE | Fan module for AOCM-60-CH09 or AOCM-60-CH09-G2 |
| AOCM-60-CH12-FAN-MODULE | Fan module for AOCM-60-CH12 or AOCM-60-CH12-G2 |
| AOCM-60-SCC-384-G2* | Switching and control card 384 Gbps (60 W) |
| AOCM-60-SCC-1536** | Switching and control card 1536 Gbps (60 W) |
| * AOCM-60-SCC-384 and AOCM-60-SCC-384-G2 are not compatible with each other in the same chassis. ** AOCM-60-SCC-1536 only used within G2 Chassis in P2P system. |
|
|
Line cards |
|
|
AOCM-60-24GE-SFP-G2 |
Line card, 20 ports 1 Gbps SFP + 4 combo ports 1 Gbps SFP/TX (55 W) |
|
AOCM-60-48GE-SFP-G2 |
Line card (Enhanced), 48 ports 1 Gbps SFP, supports MPLS, Selective QinQ (109.13 W) |
|
AOCM-60-24GE-TX-G2 |
Line card, 20 ports 10/100/1000 Mbps TX + 4 combo ports 1 Gbps SFP/TX (46.47 W) |
|
AOCM-60-48GE-TX-G2 |
Line card, 48 ports 10/100/1000 Mbps TX (88.48 W) |
|
AOCM-60-4x10GE-MPLS-G2 |
Line card, 4 port 10 Gbps SFP+, supports MPLS (82.1 W) |
|
AOCM-60-16PON-8GE-SFP-G2 |
Line card, 16 OLT EPON interfaces and 8 gigabit SFP optical interfaces (excluding the OLT SFP optical module) (110 W incl. SFPs) |
| * Power consumption not including optical transceivers except stated otherwise | |
